Understanding Essential Plumbing Skills is Crucial for Installing a Bathtub
Understanding Essential Plumbing Skills is Crucial for Installing a Bathtub
Blog Article
This article listed below about Tools You Need to Install a New Bathtub is highly enlightening. Give it a try and draw your own personal conclusions.
Installing a bath tub isn't specifically rocket science, however it does call for solid plumbing, woodworking, and also occasionally, tiling abilities. Replacing an old bath tub with a brand-new one is additionally a moderately hard task. If the old bathtub is readily available, the job can relocate quickly; if you need to open a wall surface to remove the old tub as well as place the new bath tub, the job is a lot harder. In either case, the project is within a house handyman's abilities, although you will certainly need a helper to move out the old tub and set in the new one. Make certain you have actually qualified yourself for the job as well as are comfortable trying it. As opposed to working with a contractor to take over a halfway-completed job, it is better to think about using one before you begin. Possibilities are you may need a specialist plumber to make tube links.
This short article will certainly assist you mount a brand-new bathtub in your bathroom if you have already purchased a new bathtub and also do not require to alter the setup of your previous water system pipelines.
Your tools and product list should comprise the following:
Removing Old Taps
If you need to replace old faucets with brand-new ones as a part of your installation, after that the first thing you should do is detach the water supply. After doing so, turn on the faucets to drain pipes any type of water staying in the system. The procedure of eliminating the existing faucets can be fairly bothersome because of the limited accessibility that is frequently the instance.
Make use of a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipes to the faucets. Have a cloth ready for the continuing to be water that will originate from the pipes. Once the supply pipelines have been eliminated, utilize the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the solitary taps from transforming during this procedure. When the taps have been removed, the holes in the bath/basin will need to be cleaned up of any kind of old securing substance.
Prior to going on to fit the brand-new taps, contrast the pipe connections on the old taps to the brand-new taps. If the old faucets are longer than the new taps, then a shank adapter is required for the brand-new faucets to fit.
Suitable New Taps
If the tails of the new faucets are plastic, after that you will need a plastic port to avoid damages to the string. One end of the adapter fits on the plastic tail of the tap as well as the various other end supplies a connection to the existent supply pipelines.
If you require to fit a monobloc, then you will certainly call for lowering couplers, which connects the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next off, place the tap in the placing opening in the bath/basin making sure that the washers are in location in between the tap and also the sink. Secure the tap in place with the producer offered backnut. When the tap is safely in place, the supply pipes can be linked to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with regular faucet connectors. The previous kind ought to be connected to the tap ends first, tightening only by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have been connected.
Installing the Bathtub
Using both wood boards under its feet, position the bath tub in the called for setting. The wood boards are useful in uniformly spreading out the weight of the bath tub over the area of the boards instead of focusing all the weight onto four little factors.
The following objective is to make certain that the bathtub is leveled all round. This can be achieved by inspecting the level and also changing the feet on the bathtub until the spirit level reviews degree.
To set up taps, fit the bottom of the outermost adaptable faucet port to the ideal supply pipeline by making a compression sign up with; then do the same for the other tap.
Turn on the water system as well as inspect all joints and brand-new pipework for leakages and also tighten them if essential. Load the bath tub as well as additionally inspect the overflow outlet and the regular outlet for leaks.
Ultimately, repair the bathroom paneling as defined in the manufacturer's instruction manual. Tiling and also securing around the bathtub should wait up until the tub has been utilized at the very least when as this will certainly resolve it right into its last setting.
Planning for the Installment
To start with, the supporting frame supplied with the bath must be fitted (if needed) according to the maker's guidelines. Next off, fit the faucets or mixer to the tub. When fitting the tap block, it is essential to ensure that if the tap comes with a plastic washing machine, it is fitted between the bathroom as well as the faucets. On a plastic bath, it is likewise sensible to fit a sustaining plate under the faucets device to stop strain on the tub.
Fit the versatile faucet ports to the bottom of both taps using 2 nuts and also olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet through the hole in the bathroom. Use the nut provided by the maker to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make sure you use all of the supplied washing machines.
Connect the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Attach all-time low of the overflow tube in a similar manner.The bathroom need to currently be ready to be suited its last setting.
Tiling Around the Bathtub
In the location where the bath meets the ceramic tile, it is needed to secure the joins with a silicone rubber caulking. This is essential as the fitting can relocate sufficient to split a rigid seal, triggering the water to permeate the wall in between the bathroom and also the tiling, resulting in complications with dampness and feasible leakages to the ceiling below.
You can choose from a selection of coloured sealants to assimilate your fixtures as well as installations. They are marketed in tubes and also cartridges, and also can securing gaps up to a width of 3mm (1/8 inch). If you have a larger gap to fill, you can load it with twists of drenched paper or soft rope. Keep in mind to always load the bath tub with water prior to securing, to allow for the movement experienced when the tub is in use. The sealant can split relatively very early if you do not take into account this motion prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are likewise quickly offered on the market. It is suggested to fit the tiles making use of water-resistant or water resistant sticky and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Hopefully you enjoyed reading our piece about A Step-by-Step Guide to Installing a Bathtub. Thanks so much for taking the time to read through our post. For those who enjoyed our blog post please be sure to share it. Thanks so much for taking the time to read it.
Trust our expertise. Report this page